Full Mesh Network for Ceph Server: Difference between revisions

From Proxmox VE
Jump to navigation Jump to search
(→‎/etc/frr/frr.conf: add note about increasing timeout values if informal logs show problems)
 
Line 66: Line 66:
* ens18, ens19 will be used for the actual full mesh. Physical direct connections to the other two servers, 10.15.15.y/24
* ens18, ens19 will be used for the actual full mesh. Physical direct connections to the other two servers, 10.15.15.y/24
* ens20 connection to WAN (internet/router), using at vmbr0 192.168.2.y
* ens20 connection to WAN (internet/router), using at vmbr0 192.168.2.y
* ens21 (optional) LAN (for cluster traffic, etc.) 10.14.14.y
* ens21 (optional) LAN (for Proxmox VE cluster traffic, etc.) 10.14.14.y


Direct connections between servers:
Direct connections between servers:

Latest revision as of 11:15, 15 July 2024

Introduction

This wiki page describes how to configure a three node "Meshed Network" Proxmox VE (or any other Debian based Linux distribution), which can be, for example, used for connecting Ceph Servers or nodes in a Proxmox VE Cluster with the maximum possible bandwidth and without using a switch. We recommend to use switches for clusters larger than 3 nodes or if a 3 node cluster should be expanded in the future.

The big advantage of this setup is that you can achieve a fast network connection between the nodes (10, 25, 40 or 100Gbit/s) WITHOUT buying expensive switches which can handle these fast speeds.

You need at least two available NICs in each server which each connect to one of the other servers. 

            ┌───────┐
       ┌────┤ Node1 ├────┐
       │    └───────┘    │
   ┌───┴───┐         ┌───┴───┐
   │ Node2 ├─────────┤ Node3 │
   └───────┘         └───────┘

There are a few possible ways to set up such a network:

  1. Routed (with fallback): Each packet is sent to the addressed node only. If the direct connection is down, the packets will be routed via the node in between.
  2. Routed (simple): Each packet is sent to the addressed node only
  3. RSTP: A loop with the rapid spanning tree protocol enabled
  4. Broadcast: Each packet is sent to both other nodes

Each setup has benefits and caveats. The simple routed one does not need any additional software and delivers the best performance. The routed with fallback approach delivers similar performance but can handle the loss of one connection in the mesh by routing the traffic via the middle node. Because of this, performance could be impacted in such a scenario.

The RSTP setup gives you similar fault tolerance as the routed setup with fallback. If the loop is complete, RSTP will create an artificial cut-off between two nodes, e.g. between Node 1 and Node 3. This means, Node 2 is in between Node 1 and 3 and the traffic between Node 1 and Node 3 is going via Node 2. Should a cable or NIC fail somewhere else, for example between Node 1 and Node 2, RSTP will remove the cut-off within a few seconds. Node 3 is now in between Node 1 and 2 and has to handle that traffic as well. Once the broken part has been replaced and the loop if complete again, RSTP will introduce another artificial cut-off.

The advantage of the broadcast method is an easier setup process, but it will send all data to both other nodes, using up more bandwidth.

Failure Scenarios

Loss of a Node

            ┌───────┐
       ┌────┤ Node1 ├────┐
       │    └───────┘    │
   ┌───┴───┐         ┌───┴───┐
   │ Node2 ├─────────┤ XXXXX │
   └───────┘         └───────┘

If a node is going down, for example Node 3, the Ceph and Proxmox VE cluster will remain functioning, though with reduced redundancy.

Loss of a Connection

            ┌───────┐
       ┌────┤ Node1 ├────┐
       │    └───────┘    X
   ┌───┴───┐         ┌───┴───┐
   │ Node2 ├─────────┤ Node3 │
   └───────┘         └───────┘

If one of the connections is failing, for example between Node 1 and Node 3, the resulting behavior depends on the chosen setup variant. For the RSTP and Routed (with fallback), everything will stay functioning. With RSTP it might take a short moment for it to remove the artificial cut-off. With a bit of luck, the artificial cut-off was exactly at the failed connection. When using the Routed (with fallback) setup, the traffic that used to go directly between Node 1 and Node 3 will now be routed via Node 2, resulting in a bit higher latency. This can have a bit of an impact on performance, but the cluster will stay fully functional.

For the Broadcast and Routed (simple) setups, such a situation is more problematic, because the nodes now have a different view, Node 2 can communicate with Node 3, while that is not possible for Node 1 anymore. You will see behavior such as Ceph showing the services on Node 3 to be down. To reduce the chances of a failed connection, you could combine the Broadcast and Routed (simple) with a bond to increase fault tolerance at the cost of more NICs and cables.

Example

3 servers:

  • Node1 with IP addresses x.x.x.50
  • Node2 with IP addresses x.x.x.51
  • Node3 with IP addresses x.x.x.52

3 to 4 Network ports in each server:

  • ens18, ens19 will be used for the actual full mesh. Physical direct connections to the other two servers, 10.15.15.y/24
  • ens20 connection to WAN (internet/router), using at vmbr0 192.168.2.y
  • ens21 (optional) LAN (for Proxmox VE cluster traffic, etc.) 10.14.14.y

Direct connections between servers:

  • Node1/ens18 - Node2/ens19
  • Node2/ens18 - Node3/ens19
  • Node3/ens18 - Node1/ens19

Please adapt the NIC names and IP addresses according to your situation. 

                    ┌───────────┐
                    │   Node1   │
                    ├─────┬─────┤
                    │ens18│ens19│
                    └──┬──┴──┬──┘
                       │     │
┌───────┬─────┐        │     │        ┌─────┬───────┐
│       │ens19├────────┘     └────────┤ens18│       │
│ Node2 ├─────┤                       ├─────┤ Node3 │
│       │ens18├───────────────────────┤ens19│       │
└───────┴─────┘                       └─────┴───────┘

Routed Setup (with Fallback)

We can make use of the OpenFabric protocoll which is a routing protocol derived from IS-IS, providing link-state routing. FRR has a working implementation.

Yellowpin.svg Note: This will not work in combination with the EVPN functionality from the Proxmox VE SDN as it will overwrite our FRR configuration
Yellowpin.svg Note: If you install Ceph afterwards, you will have to do the initial Ceph configuration on the command line

First install FRR: 

apt install frr

/etc/frr/daemons

Enable the OpenFabric daemon by changing the line in /etc/frr/daemons to "yes": 

[...]
fabricd=yes
[...]

/etc/frr/frr.conf

In this config file, 3 parameters need to be changed for each node:

  • hostname
  • IP address
  • NET

The IP addresses, in our example, are the ones in the 10.15.15.y/24 network.

The System ID in the NET (network entity title) needs to be unique. For example we can use the following ones for the three nodes:

  • 49.0001.1111.1111.1111.00
  • 49.0001.2222.2222.2222.00
  • 49.0001.3333.3333.3333.00


By configuring very short interval times, we can achieve almost instantaneous failover. 

# default to using syslog. /etc/rsyslog.d/45-frr.conf places the log in
# /var/log/frr/frr.log
#
# Note:
# FRR's configuration shell, vtysh, dynamically edits the live, in-memory
# configuration while FRR is running. When instructed, vtysh will persist the
# live configuration to this file, overwriting its contents. If you want to
# avoid this, you can edit this file manually before starting FRR, or instruct
# vtysh to write configuration to a different file.

frr defaults traditional
hostname node1
log syslog warning
ip forwarding
no ipv6 forwarding
service integrated-vtysh-config
!
interface lo
 ip address 10.15.15.50/32
 ip router openfabric 1
 openfabric passive
!
interface ens18
 ip router openfabric 1
 openfabric csnp-interval 2
 openfabric hello-interval 1
 openfabric hello-multiplier 2
!
interface ens19
 ip router openfabric 1
 openfabric csnp-interval 2
 openfabric hello-interval 1
 openfabric hello-multiplier 2
!
line vty
!
router openfabric 1
 net 49.0001.1111.1111.1111.00
 lsp-gen-interval 1
 max-lsp-lifetime 600
 lsp-refresh-interval 180


Yellowpin.svg Note: If the log level is set to informational, you might see log messages like 
OpenFabric: Initial synchronization on enp1s0f0np0 timed out!

In that case, consider to increase the timeout values in each interface section for

  • csnp-interval
  • hello-interval
  • hello-multiplier

and in the router section

  • lsp-gen-interval

/etc/network/interfaces

The network configuration itself is rather simple. We need to bring the interfaces used for the mesh network up. If we plan to use a large MTU, configure it here.

Do note the last line! It causes FRR to be restarted if we do apply any changes to the network configuration. For example by clicking the "Apply Configuration" button in the Proxmox VE GUI. 

auto lo
iface lo inet loopback

iface ens20 inet manual

auto ens21
iface ens21 inet static
        address  10.14.14.51
        netmask  255.255.255.0

auto vmbr0
iface vmbr0 inet static
        address  192.168.2.51
        netmask  255.255.240.0
        gateway  192.168.2.1
        bridge_ports ens20
        bridge_stp off
        bridge_fd 0

auto ens18
iface ens18 inet static
        mtu 9000

auto ens19
iface ens19 inet static
        mtu 9000

post-up /usr/bin/systemctl restart frr.service

To apply the changes without a reboot, run the following commands: 

ifreload -a
systemctl restart frr.service

You can check the status via the FRR CLI. 

vtysh

Then enter one of the commands detailed in the FRR OpenFabric documentation. For example, "show openfabric route".


Ceph Initialization

Since the IPs are configured in the FRR configuration and not in the /etc/network/interfaces file, the Ceph GUI configuration assistant won't show it to you. To do the initial Ceph configuration, run 

pveceph init --network 10.15.15.50/24

If you plan to use the Ceph Cluster Network on a different network, add the "--cluster-network" option. Next you will need to create the first monitor to get Ceph running. Either do that on the GUI or via the CLI on the node you just installed Ceph on with 

pveceph mon create

Routed Setup (Simple)

The 3 nodes have to be configured as described in the following sections. Note that multicast is not possible with this method.

Node1

/etc/network/interface

auto lo
iface lo inet loopback

iface ens20 inet manual

auto ens21
iface ens21 inet static
        address  10.14.14.50
        netmask  255.255.255.0

# Connected to Node2 (.51)
auto ens18
iface ens18 inet static
        address  10.15.15.50
        netmask  255.255.255.0
        up ip route add 10.15.15.51/32 dev ens18
        down ip route del 10.15.15.51/32

# Connected to Node3 (.52)
auto ens19
iface ens19 inet static
        address  10.15.15.50
        netmask  255.255.255.0
        up ip route add 10.15.15.52/32 dev ens19
        down ip route del 10.15.15.52/32

auto vmbr0
iface vmbr0 inet static
        address  192.168.2.50
        netmask  255.255.240.0
        gateway  192.168.2.1
        bridge_ports ens20
        bridge_stp off
        bridge_fd 0

Route

root@pve-2-50:~# ip route
default via 192.168.2.1 dev vmbr0 onlink 
10.14.14.0/24 dev ens21 proto kernel scope link src 10.14.14.50 
10.15.15.0/24 dev ens18 proto kernel scope link src 10.15.15.50 
10.15.15.0/24 dev ens19 proto kernel scope link src 10.15.15.50 
10.15.15.52 dev ens19 scope link 
10.15.15.51 dev ens18 scope link 
192.168.0.0/20 dev vmbr0 proto kernel scope link src 192.168.2.50

Node2

/etc/network/interface

auto lo
iface lo inet loopback

iface ens20 inet manual

auto ens21
iface ens21 inet static
        address  10.14.14.51
        netmask  255.255.255.0

# Connected to Node3 (.52)
auto ens18
iface ens18 inet static
        address  10.15.15.51
        netmask  255.255.255.0
        up ip route add 10.15.15.52/32 dev ens18
        down ip route del 10.15.15.52/32

# Connected to Node1 (.50)
auto ens19
iface ens19 inet static
        address  10.15.15.51
        netmask  255.255.255.0
        up ip route add 10.15.15.50/32 dev ens19
        down ip route del 10.15.15.50/32

auto vmbr0
iface vmbr0 inet static
        address  192.168.2.51
        netmask  255.255.240.0
        gateway  192.168.2.1
        bridge_ports ens20
        bridge_stp off
        bridge_fd 0

Route

root@pve-2-51:/# ip route
default via 192.168.2.1 dev vmbr0 onlink 
10.14.14.0/24 dev ens21 proto kernel scope link src 10.14.14.51 
10.15.15.0/24 dev ens18 proto kernel scope link src 10.15.15.51 
10.15.15.0/24 dev ens19 proto kernel scope link src 10.15.15.51 
10.15.15.52 dev ens18 scope link 
10.15.15.50 dev ens19 scope link 
192.168.0.0/20 dev vmbr0 proto kernel scope link src 192.168.2.51

Node3

/etc/network/interface

auto lo
iface lo inet loopback

iface ens20 inet manual

auto ens21
iface ens21 inet static
        address  10.14.14.52
        netmask  255.255.255.0

# Connected to Node1 (.50)
auto ens18
iface ens18 inet static
        address  10.15.15.52
        netmask  255.255.255.0
        up ip route add 10.15.15.50/32 dev ens18
        down ip route del 10.15.15.50/32

# Connected to Node2 (.51)
auto ens19
iface ens19 inet static
        address  10.15.15.52
        netmask  255.255.255.0
        up ip route add 10.15.15.51/32 dev ens19
        down ip route del 10.15.15.51/32

auto vmbr0
iface vmbr0 inet static
        address  192.168.2.52
        netmask  255.255.240.0
        gateway  192.168.2.1
        bridge_ports ens20
        bridge_stp off
        bridge_fd 0

Route

root@pve-2-52:~# ip route
default via 192.168.2.1 dev vmbr0 onlink 
10.14.14.0/24 dev ens21 proto kernel scope link src 10.14.14.52 
10.15.15.0/24 dev ens18 proto kernel scope link src 10.15.15.52 
10.15.15.0/24 dev ens19 proto kernel scope link src 10.15.15.52 
10.15.15.51 dev ens19 scope link 
10.15.15.50 dev ens18 scope link 
192.168.0.0/20 dev vmbr0 proto kernel scope link src 192.168.2.52

RSTP Loop Setup

This setup requires the use of Open vSwitch (OVS) as it supports RSTP (Rapid spanning tree protocol). The Linux bridge itself only supports STP (without the rapid) which usually needs too long to react to a changed topology. In our tests we saw the RSTP setup to recover from one network connection going down within a few seconds while STP took about 30 seconds. This is long enough for Ceph to start to complain and throw some warnings.

First the package `openvswitch-switch` needs to be installed on all nodes: 

apt install openvswitch-switch

The network configuration will look the same for each node, except for the IP addresses.

/etc/network/interface

auto lo
iface lo inet loopback

iface ens20 inet manual

auto ens21
iface ens21 inet static
        address  10.14.14.51
        netmask  255.255.255.0

auto vmbr0
iface vmbr0 inet static
        address  192.168.2.51
        netmask  255.255.240.0
        gateway  192.168.2.1
        bridge_ports ens20
        bridge_stp off
        bridge_fd 0

auto ens18
iface ens18 inet manual
    ovs_type OVSPort
    ovs_bridge vmbr1
    ovs_options other_config:rstp-enable=true other_config:rstp-path-cost=150 other_config:rstp-port-admin-edge=false other_config:rstp-port-auto-edge=false other_config:rstp-port-mcheck=true vlan_mode=native-untagged

auto ens19
iface ens19 inet manual
    ovs_type OVSPort
    ovs_bridge vmbr1
    ovs_options other_config:rstp-enable=true other_config:rstp-path-cost=150 other_config:rstp-port-admin-edge=false other_config:rstp-port-auto-edge=false other_config:rstp-port-mcheck=true vlan_mode=native-untagged

auto vmbr1
iface vmbr1 inet static
    address 10.15.15.50/24
    ovs_type OVSBridge
    ovs_ports ens18 ens19
    up ovs-vsctl set Bridge ${IFACE} rstp_enable=true other_config:rstp-priority=32768 other_config:rstp-forward-delay=4 other_config:rstp-max-age=6
    post-up sleep 10

If needed, you can set the MTU with `ovs_mtu 9000` in the `vmbr1`, `eno18` and `eno19` configs. You can check the RSTP status with 

ovs-appctl rstp/show

Broadcast Setup

Create a "broadcast" bond with the given interfaces on every node. This can be done over the GUI or on the command-line.

GUI

On the GUI go to the node level -> System -> Network. Then click on "Create" and select "Linux Bond". In the Wizard make your configuration without a gateway and set mode to "broadcast".

Reboot the node to activate the new network settings.

Command-Line

Add the following lines to '/etc/network/interfaces'. 

auto bond<No>
iface bond<No> inet static
	address  <IP>
	netmask  <Netmask>
	slaves <Nic1> <Nic2>
	bond_miimon 100
	bond_mode broadcast
#Full Mesh

Then start the bond 

ifup bond<No>

In Node1 of the above described setup example /etc/network/interface will look like as follows: 

iface lo inet loopback

iface ens20 inet manual

auto ens21
iface ens21 inet static
        address  10.14.14.50
        netmask  255.255.255.0


iface ens18 inet manual

iface ens19 inet manual

auto bond0
iface bond0 inet static
       address 10.15.15.50
       netmask 255.255.255.0
       slaves ens18 ens19
       bond_miimon 100
       bond_mode broadcast


auto vmbr0
iface vmbr0 inet static
        address  192.168.2.50
        netmask  255.255.240.0
        gateway  192.168.2.1
        bridge_ports ens20
        bridge_stp off
        bridge_fd 0
Retrieved from "https://pve.proxmox.com/mediawiki/index.php?title=Full_Mesh_Network_for_Ceph_Server&oldid=12009"