PVE-zsync

Introduction

With the Proxmox VE ZFS replication manager (pve-zsync) you can synchronize your virtual machine (virtual disks and VM configuration) or directory stored on ZFS between two servers. By synchronizing, you have a full copy of your virtual machine on the second host and you can start your virtual machines on the second server (in case of data loss on the first server).

By default, the tool is syncing every 15 minutes, but the synchronization interval is fully configurable via the integrated cron job setup. The configuration of pve-zsync can be done either on the source server or on the target server.

This is useful for advanced backup strategies.

Note: pve-zsync is introduced for Proxmox VE 3.4 as technology preview. The package can be installed on plain Debian Wheezy or Jessie servers too, as long as ZFS is configured.

Main features

• Speed limiter
• Syncing interval can be set by cron
• Syncing VM (disks and config) but also ZFS Datasets
• Can keep multiple backups
• Can be used in both directions
• Can send on local host
• Traffic is encrypted

Limitations

• not possible to sync recursive
• only ssh for transfer
• email notification is done by cron

System requirements

• Both, target and source server must support ZFS (best practice: use Proxmox VE hosts).
• SSH must be installed and configured
• to receive email-notifications, a working mail server is required (e.g. postfix).
• cstream
• perl
• scp

Configuration and use

Install the package with apt, on your Proxmox VE host:

apt-get install pve-zsync

This tool need basically no configuration. On the the first usage, when you create a job with a unknown host, the tool will ask you about the password for the remote server.

Sync a VM or ZFS dataset one time

This is also possible if a recurring job exists, here you must have in mind that the naming must be the same.

root@zfs1:~# pve-zsync sync --source 100 --dest 192.168.1.2:tank/backup --verbose --maxsnap 2 --name test1 --limit 512

This command sync VM 100 witch is located on the server where the tool is called and sent it to the server 192.168.1.2 on the zpool tank which has an subset backup. the maxsnap tells, that it should be kept 2 backups, if there are more then 2 backups, the 3 one will be erased (sorted by creation time). Name is only reasonable, if there already a sync job. limit sets the speed limit what is used for syncing, here it would be 512 KBytes/s.

Create a recurring sync job

root@zfs1:~# pve-zsync create --source 192.168.1.1:100 --dest tank/backup --verbose --maxsnap 2 --name test1 --limit 512 --skip

The skip parameter disable the initial sync, what normally will be done immediately, but can take a wile, dependent on the size of the backup. The initial sync will be done at the first sync time.

Delete a recurring sync job

if you delete a job, the former backup data will not be erased only the config will be erased.

root@zfs1:~# pve-zsync destroy --source 192.168.1.1:100 --name test1

Name is not necessary if it is default.

Pause a sync job

If you want to pause a job, say maintenance the source server!

root@zfs1:~# pve-zsync disable --source 192.168.1.1:100 --name test1

Reactivate a sync job

to reactivate a job, because the job was paused or the job failed use.

root@zfs1:~# pve-zsync enable --source 192.168.1.1:100 --name test1

This will reset the error flag in case of failure.

Changing parameters

You can edit the configuration in /etc/cron.d/pve-zsync or destroy the job and create it new.

Information about the jobs

To get a overview about all jobs use:

root@zfs1:~# pve-zsync list
SOURCE                   NAME           STATE LAST SYNC           TYPE 
192.168.15.95:100        testing1       ok     2015-05-13_14:44:00 ssh  
192.168.15.95:data/test1 testing1       syncing2015-05-13_14:44:11 ssh  

root@zfs1:~# pve-zsync status
SOURCE                   NAME           STATUS 
192.168.15.95:100        testing1       ok    
192.168.15.95:data/test1 testing1       syncing 

Recovering an VM

You must recover the VM or dataset manually. (In one of the upcoming releases, the restore for Proxmox VE VM will be integrated).

Fist, stop the sync job for the VM or dataset in question.

NOTE: if not you can be interfere the sync job or your snapshot will removed before you are able to send it.

pve-zsync disable --source 192.168.15.2:100 --name test
pve-zsync list
SOURCE                   NAME           STATE  LAST SYNC           TYPE 
192.168.15.2:100        test            stopped2015-06-12_11:03:01 ssh  

Then you can send the VM or Dataset to the selected target. SSH is only needed if you send to a remote sever.

zfs send <pool>/[<path>/]vm-<VMID>-disk-<number>@<last_snapshot> | [ssh root@<destination>] zfs receive <pool>/<path>/vm-<VMID>-disk-<number>

If you have a VM you must also copy the config and you need to correct the virtual disk storage configuration accordingly.

cp /var/lib/pve-zsync/<VMID>.conf.rep_<JOB_NAME><VMID>_<TIMESTAMP> /etc/pve/qemu-server/<VMID>.conf

Example restore VM 100 with 2 disk on server 192.168.15.2 and change VMID from 100 to 200:

zfs send rpool/backup/vm-100-disk-1@rep_test100_2015-06-12_11:03:01 | ssh root@192.168.15.2 zfs receive vm/vm-200-disk-1
ssh root@192.168.15.2
cp /var/lib/pve-zsync/100.conf.rep_test100_2015-06-11_14:11:01 /etc/pve/qemu-server/200.conf
nano /etc/pve/qemu-server/200.conf

Now you have to change the storage path:

bootdisk: virtio0
cores: 1
memory: 512
name: Debian8min
net0: virtio=12:5E:F6:59:A9:BB,bridge=vmbr0
numa: 0
ostype: l26
smbios1: uuid=11fa2fba-5670-4610-aabb-534ad7edeffe
sockets: 1
virtio0: zfs:vm-100-disk-1,size=10G
virtio1: zfs:vm-100-disk-2,size=10G

to

bootdisk: virtio0
cores: 1
memory: 512
name: Debian8min
net0: virtio=12:5E:F6:59:A9:BB,bridge=vmbr0
numa: 0
ostype: l26
smbios1: uuid=11fa2fba-5670-4610-aabb-534ad7edeffe
sockets: 1
virtio0: vm:vm-200-disk-1,size=10G
virtio1: vm:vm-200-disk-2,size=10G

Troubelshooting

tbd.

Video Tutorials

Proxmox VE Youtube channel