tbd, if possible, detailed answers should linked to internal wiki pages
- 1 General
- 2 Installation and upgrade
- 3 Hardware
- 4 Networking
- 5 Virtualization
- 6 Troubleshooting
What is a container, CT, VE, Virtual Private Server, VPS?
What is a KVM guest (KVM VM)?
- A KVM guest or KVM VM is a guest system running virtualized under Proxmox VE with KVM.
What distribution is Proxmox VE based on?
- Proxmox VE is based on Debian GNU/Linux, Proxmox VE Kernel is based on RHEL6 Kernel with OpenVZ patches
Installation and upgrade
Where can I find installation instructions?
- See Installation
Proxmox VE command line tools
How long will my Proxmox version be supported?
|Proxmox Version||Debian Version||EOL||LTS|
|Proxmox 4.x||Debian 8 (Jessie)||2018-05||2020-04/05 (not announced yet)|
|Proxmox 3.x||Debian 7 (Wheezy)||2016-04-26||2018-05-31|
|Proxmox 2.x||Debian 6 (Squeezy)||2014-05||2016-02-29|
Will Proxmox VE run on a 32bit processor?
Proxmox VE works only on 64-bit CPU´s (AMD or Intel). There is no plan for 32-bit for the platform.
There are, however, unofficial (and unsupported) instructions for manually installing Proxmox on 32-bit systems:
- Proxmox 2.0 on Squeeze Install Proxmox VE on Debian Squeeze on 32-Bit Processor
- Proxmox 1.4 on Lenny Install Proxmox VE on Debian Lenny on 32-Bit Processor
Supported CPU chips
To check if your CPU is virtualization compatible, check for the "vmx" or "svm" tag in this command output:
egrep '(vmx|svm)' /proc/cpuinfo
64-bit processors with Intel Virtualization Technology (Intel VT-x) support
64-bit processors with AMD Virtualization Technology (AMD-V) support
How do I configure bridged networking in an OpenVZ Ubuntu/Debian container?
- In the web gui under Virtual Machine configuration go to the network tab.
- Remove the ip address for venet and save. (Bridged Ethernet Devices will appear)
- SSH into your host system and enter the container you want set bridged networking for: # vzctl enter <VMID>
- edit /etc/network/interfaces using using the following format and save. (replace with settings for your network)
auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 10.0.0.17 netmask 255.255.255.0 network 10.0.0.0 broadcast 10.0.0.255 gateway 10.0.0.10
- Shutdown the container.
- Go back to web gui and under "Bridged Ethernet Devices" configure eth0 to vmbr0 and save. (a mac address will be automatically assigned)
- Start the container.
Finally check that networking is working by entering the guest and viewing the results of ifconfig
- In a Centos/RHEL container, check the gateway device is set correctly.
NETWORKING="yes" #GATEWAYDEV="venet0" # comment this and add line below GATEWAYDEV="eth0" HOSTNAME="hostname" # should be set by proxmox GATEWAY=184.108.40.206 # CHANGE (and remove from ifcfg-eth0)
Why do you recommend 32-bit guests over 64 bit guests?
- 64-bit makes sense only if you need greater than 4GB of memory.
- 32-bit guests use less memory in certain situations
- e.g. a standard installation of apache2 on 64 bit containers consumes much more memory than on 32 bit.
See Troubleshooting page.