tbd, if possible, detailed answers should linked to internal wiki pages
- 1 General
- 2 Installation and upgrade
- 3 Networking
- 4 Troubleshooting
What is a container, CT, VE, Virtual Private Server, VPS?
What is a KVM guest (KVM VM)?
A KVM guest or KVM VM is a guest system running virtualized under Proxmox VE with KVM.
What is a Virtual Appliance?
Installation and upgrade
Where can I find installation instructions?
- See Installation
How do I configure bridged networking in an OpenVZ Ubuntu/Debian container?
1. In the web gui under Virtual Machine configuration got to the network tab.
2. Remove the ip address for venet and save. (Bridged Ethernet Devices will appear)
3. SSH into your host system and enter the container you want set bridge networking for:
# vzctl enter <VMID>
4. edit /etc/network/interfaces using using the following format and save. (replace with settings for your network)
auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 10.0.0.17 netmask 255.255.255.0 network 10.0.0.0 broadcast 10.0.0.255 gateway 10.0.0.10
5. Shutdown the container.
6. Go back to web gui and under "Bridged Ethernet Devices" configure eth0 to vmbr0 and save. (a mac address will be automatically assigned)
7. Start the container.
Finally check that networking is working by entering the guest and viewing the results of ifconfig
I can't switch virtual consoles in Linux KVM guests with alt-F1, alt-F2...
VNC viewer does not pass some key combinations or they may be intercepted by your operating system.
To send custom key combinations to the guest, go to "Monitor" in Virtual Machine Configuration for a given guest and use "sendkey" command.
For example, to switch to the third console (tty3) you would use:
How can I send sysrq to Linux KVM guests?
Similarly to the above, go to "Monitor" in Virtual Machine Configuration for a given guest and use "sendkey" command.
For example, to issue "Emergency Sync", you would use:
In the VNC viewer for the given guest you should see:
SysRq : Emergency Sync
You should also see this entry if you run "dmesg" on this guest.
See also http://en.wikipedia.org/wiki/Magic_SysRq_key for a full reference of possible combinations.
How can I access Linux guests through a serial console?
Sometimes, it is necessary to access the guest through a serial console:
- you lost network access to the guest and VNC is either too slow for you or don't have the features you need (i.e. easy copy/paste between other terminals)
- your guest freezes or kernel panics, you want to debug it, but it's impossible to capture all messages on VNC screen
- you are familiar with
xm console <guest>from Xen and you want to use a similar feature here
The necessary steps are:
- on Proxmox VE host, in guest's configuration file in
args: -serial unix:/var/run/qemu-server/<VMID>.serial,server,nowait
This will open console in
/var/run/qemu-server/<VMID>.serial socket file, which can be accessed by minicom or other serial communication program.
An alternative is to add:
args: -serial tcp:localhost:6000,server,nowait
With this, you can connect to guest's serial console with telnet. Note that with telnet, any passwords will be visible on the screen.
- on guest, in /etc/inittab, look for lines similar to the ones below and make sure you have "ttyS0" there - this would be your serial console:
5:2345:respawn:/sbin/mingetty tty5 6:2345:respawn:/sbin/mingetty ttyS0
If you want kernel messages to be shown on both serial and VGA consoles, you have to add a kernel parameter in your bootloader's configuration. For grub, it would be these "console" entries:
kernel (hd0,0)/boot/vmlinuz root=LABEL=guest-root console=ttyS0 console=tty0
To access the guest from minicom, configure it to use a path such as
unix#/var/run/qemu-server/<VMID>.serial in "cOnfigure Minicom -> Serial port setup -> Serial Device".
To use multiple minicom configurations for several guests, create a file like /etc/minicom/minirc.someguest for each of your guests, with contents:
pu port unix#/var/run/qemu-server/<VMID>.serial pu minit pu mreset
Then, start the console with:
How can I assign a physical disk to a VM?
Add it first in the web interface, then use:
qm set <vmid> -ide# /dev/sdb
qm set <vmid> -ide# /dev/disk/by-id/[your disk ID]
...since having the drive letter change (should you add a drive) might have unintended consequences.
Also see /etc/qemu-server/<vmid>.conf