[PVE-User] Load modules into the VPS

[Maykel Franco Hernández]

Hi, I probed the command: 

vzctl set 100 --capability net_admin:on
--save 

And in the container exec lsmod and not results...


root at test1-mysql:~# lsmod
Module Size Used by

And I restart to openvz
with /etc/init.d/vz restart in proxmox 2.0.

The network devices in the
container is venet or veth??

root at test1-mysql:~# ifconfig
lo Link
encap:Local Loopback 
 inet addr:127.0.0.1 Mask:255.0.0.0
 inet6 addr:
::1/128 Scope:Host
 UP LOOPBACK RUNNING MTU:16436 Metric:1
 RX packets:8
errors:0 dropped:0 overruns:0 frame:0
 TX packets:8 errors:0 dropped:0
overruns:0 carrier:0
 collisions:0 txqueuelen:0 
 RX bytes:400 (400.0 B)
TX bytes:400 (400.0 B)

venet0 Link encap:UNSPEC HWaddr
00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 
 inet addr:127.0.0.2
P-t-P:127.0.0.2 Bcast:0.0.0.0 Mask:255.0.0.0
 UP BROADCAST POINTOPOINT
RUNNING NOARP MTU:1500 Metric:1
 RX packets:379 errors:0 dropped:0
overruns:0 frame:0
 TX packets:288 errors:0 dropped:0 overruns:0
carrier:0
 collisions:0 txqueuelen:0 
 RX bytes:30571 (30.5 KB) TX
bytes:34542 (34.5 KB)

venet0:0 Link encap:UNSPEC HWaddr
00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 
 inet addr:10.0.0.155
P-t-P:10.100.100.155 Bcast:0.0.0.0 Mask:255.0.0.0
 UP BROADCAST
POINTOPOINT RUNNING NOARP MTU:1500 Metric:1

Can anybody help me
please??

El 2012-04-16 18:20, Maykel Franco Hernández escribió: 

>
Thanks very much. I probed tomorrow. 
> 
> Thanks again. 
> 
> El
2012-04-16 17:54, Timh B escribió: 
> 
>> Hi,
>> 
>> Usually loading the
modules on the hardware node is enough, in some cases
>> you might need
"vzctl set--save --capability net_admin:on" if it
>> does anything
special with the network devices. I've only found this
>> useful for
doing DHCP/PXE so far though. In some rare cases you might want
>> to
restart openvz after you've added modules to the hardware node;
>>
/etc/init.d/vz restart.
>> 
>> Good luck!
>> 
>> BR,
>> Timh
>> 
>> On
Mon, April 16, 2012 17:25, Maykel Franco Hernández wrote:
>> 
>>> Hi!!
Before I tell everything, Congratulations for PROXMOX 2.0. I installed
the proxmox and I test this tool. All OK, but I created the container
ubuntu 10.04 and I need load the modules for the loadbalancing in this
VPS container ubuntu.: modprobe ip_vs_dh modprobe ip_vs_ftp modprobe
ip_vs modprobe ip_vs_lblc modprobe ip_vs_lblcr modprobe ip_vs_lc
modprobe ip_vs_nq modprobe ip_vs_rr modprobe ip_vs_sed modprobe ip_vs_sh
modprobe ip_vs_wlc modprobe ip_vs_wrr # modprobe ip_vs_dh WARNING:
Deprecated config file /etc/modprobe.conf, all config files belong into
/etc/modprobe.d/. FATAL: Module ip_vs_dh not found. But in the proxmox
the modules are loaded successfull: For example: root at proxmox1:~#
modprobe ip_vs_dh root at proxmox1:~# lsmod | grep ip nf_conntrack_ipv4
9946 2 nf_nat nf_conntrack 80789 3 vzrst,nf_nat,nf_conntrack_ipv4
nf_defrag_ipv4 1531 1 nf_conntrack_ipv4 ip6t_REJECT 4743 0
ip6table_mangle 3637 0 ip6table_filter 3001 0 ip6_tables 19714 2
ip6table_mangle,ip6table_filter iptable_mangle 3461 0 iptable_filter
2905 0 xt_multiport 2812 0 ipt_REJECT 2431 0 ip_tables 18151 2
iptable_mangle,iptable_filter ip_vs_wrr 2291 0 ip_vs_wlc 1257 0 ip_vs_sh
2061 0 ip_vs_sed 1257 0 ip_vs_rr 1436 0 ip_vs_nq 1222 0 ip_vs_lc 1190 0
ip_vs_lblcr 5735 0 ip_vs_lblc 4235 0 ip_vs_ftp 3626 0 ip_vs_dh 1997 0
ip_vs 108414 22
ip_vs_wrr,ip_vs_wlc,ip_vs_sh,ip_vs_sed,ip_vs_rr,ip_vs_nq,ip_vs_lc,ip_vs_lblcr,ip_vs_lblc,ip_vs_ftp,ip_vs_dh
ipv6 326645 333 vzrst,ip6t_REJECT,ip6table_mangle,ib_addr,ip_vs I found
in google what the modules are loaded in proxmox, not a VPS. And from
proxmox share this modules in the VPS openvz. I found in google this
example: vzctl set 101 --iptables iptable_filter --iptables ipt_length
--iptables ipt_limit --iptables iptable_mangle --iptables ipt_REJECT
--save But I need load the modules ip_vs....... Can I help me please??
_______________________________________________ pve-user mailing list
pve-user at pve.proxmox.com [1]
http://pve.proxmox.com/cgi-bin/mailman/listinfo/pve-user [2]
>> 
>> --
Timh

 

Links:
------
[1] mailto:pve-user at pve.proxmox.com
[2]
http://pve.proxmox.com/cgi-bin/mailman/listinfo/pve-user
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.proxmox.com/pipermail/pve-user/attachments/20120417/d2e402e4/attachment.htm>