Windows 10 guest best practices: Difference between revisions

From Proxmox VE
Jump to navigation Jump to search
Line 30: Line 30:
If you miss some VirtIO drivers, you may install them as follows on a running system.
If you miss some VirtIO drivers, you may install them as follows on a running system.


To do so, start the file explorer, select the CDROM drive with the VirtIO iso image mounted and browse to the folder folder of the desired component. Some often needed, using the [https://fedorapeople.org/groups/virt/virtio-win/direct-downloads/archive-virtio/virtio-win-0.1.105-1/virtio-win-0.1.105.iso virtio-win-0.1.105] version, are:
To do so, start the file explorer, select the CDROM drive with the VirtIO iso image mounted and browse to the folder folder of the desired component. Some often needed, using the [https://fedorapeople.org/groups/virt/virtio-win/direct-downloads/archive-virtio/virtio-win-0.1.105-1/virtio-win-0.1.118.iso virtio-win-0.1.118] version, are:
* Ethernet Adapter: NetKVM\w8.1\amd64 here right-click the setup information file "netkvm" and select install.
* Ethernet Adapter: NetKVM\w8.1\amd64 here right-click the setup information file "netkvm" and select install.
* Virtual Memory Balloon Driver: Balloon\w8.1\amd64 here right-click the setup information file "balloon" and select install.
* Virtual Memory Balloon Driver: Balloon\w8.1\amd64 here right-click the setup information file "balloon" and select install.

Revision as of 07:10, 4 July 2016

Introduction

This is a set of best practices to follow when installing a Windows 10 guest on a Proxmox VE server 4.x (4.2 at time of writing). Right now it's a work in progress.

Install

Prepare

To obtain a good level of performance, we will install the Windows VirtIO Drivers during the Windows installation.

  • Create a new VM, select "Microsoft Windows 8/2012" continue and mount your Windows 10 ISO in the CDROM drive
  • For your virtual hard disk select "VirtIO" as bus and "Write back" as cache option for best performance.
  • Configure your memory settings as needed, continue and set "VirtIO (paravirtualized)" as network device, finish your VM creation.
  • For the VirtIO drivers, upload the driver ISO (successfully tested with "virtio-win-0.1.105.iso", get it from here) to your storage, create a new CDROM drive (use "Add -> CD/DVD drive" in the hardware tab), and load the Virtio Drivers ISO in the new virtual CDROM drive
  • Now your ready to start the VM, just follow the Windows installer.

Launch Windows install

  • After starting your VM launch the console
  • Follow the installer steps until you reach the installation type selection where you need to select "Custom (advanced)"
  • Now click "Load driver" to install the VirtIO drivers for hard disk and the network. (successfully tested with "virtio-win-0.1.118.iso")
    • hard disk: Browse to the CD drive where you mounted the VirtIO driver and select folder "viostor\w8.1\amd64" and confirm. Select the "Red Hat VirtIO SCSI controller" and click next to install it. Now you should see your drive.
    • Network: Repeat the steps from above (click again "Load driver", etc.) and select the folder "NetKVM\w8.1\amd64", confirm it and select "Redhat VirtIO Ethernet Adapter" and click next.
    • Memory Ballooning: Again, repeat the steps but this time select the "Balloon\w8.1\amd64" folder, then the "VirtIO Balloon Driver" and install it by clicking next. With these three drivers you should be good covered to run a fast virtualized Windows 10 system.
  • Choose the drive and continue the Windows installer steps.

Install additional VirtIO drivers on running System

See also: Paravirtualized Block Drivers for Windows
VirtIO Ethernet Installation

If you miss some VirtIO drivers, you may install them as follows on a running system.

To do so, start the file explorer, select the CDROM drive with the VirtIO iso image mounted and browse to the folder folder of the desired component. Some often needed, using the virtio-win-0.1.118 version, are:

  • Ethernet Adapter: NetKVM\w8.1\amd64 here right-click the setup information file "netkvm" and select install.
  • Virtual Memory Balloon Driver: Balloon\w8.1\amd64 here right-click the setup information file "balloon" and select install.
  • Hard disk: viostor\w8.1\amd64 here right-click the setup information file "viostor" and select install.

After the installation process the device should work as expected.

For more information and configuration about ballooning, see Dynamic Memory Management

Further information

Disk-Image Format: raw vs qcow2

Raw file format provides slightly better performance while qcow2 offers advanced features such as copy on write and Live_Snapshots. Since V2.3, qcow2 is the default format.

VirtIO drivers

Make it really easy: Build your ISO with drivers already included: Windows guests - build ISOs including VirtIO drivers

Latest iso with VirtIO drivers : https://fedoraproject.org/wiki/Windows_Virtio_Drivers

See also

Windows 2012 guest best practices

Windows 8 guest best practices