Dynamic Memory Management

From Proxmox VE
Jump to navigation Jump to search

Introduction

Optimized and effective memory management is a key factor in virtualization environments. KSM and Auto-Ballooning enables sophisticated and economic configurations for physical RAM utilization.

KSM

KSM (Kernel Samepage Merging) is running in the Linux kernel and scans the memory of all the virtual machines running on a single host, looking for duplication and consolidating. With KSM we're able to improve virtual machine density by as much as 300% without impacting performance. One of the great benefits of using Linux as the hypervisor means KSM is not limited to KVM and virtual machines, but can also reduce memory pressure with normal Linux applications.

It was integrated in PVE since version 1.5, and is implemented with the package "ksm-control-daemon" (check your version with the cli command "pveversion -v").

KSM in action

Just install several KVM virtual machines with the same OS (using at least 80% of your physical memory on the host) and wait a few minutes. You will notice higher CPU activities on the host (ksm daemon) and the used memory on the host will be lowered significantly (see start page showing the overall memory usage).

Howto verify that KSM is working (how many pages are being shared between your KVM guests):

watch cat /sys/kernel/mm/ksm/pages_sharing

Note: a page is 4096 bytes

The file /etc/ksmtuned.conf allows for some customization of its behaviour.

See also

Disable KSM

If you don't care about memory optimization but care about save CPU overhead produced by KSM, in Proxmox >= 4.x you can disable it with:

systemctl disable ksmtuned

and reboot

Ballooning

Memory ballooning (KVM only) allows you to have your guest dynamically change it’s memory usage by evicting unused memory during run time. It reduces the impact your guest can have on memory usage of your host by giving up unused memory back to the host.

The Proxmox VE host can loan ballooned memory to a busy VM. The VM decides which processes or cache pages to swap out to free up memory for the balloon. The VM (Windows or Linux) knows best which memory regions it can give up without impacting performance of the VM.

Note that the Guest cannot ask for the memory back until the host has 'deflated' this balloon. If set too aggressively, some applications in the guest may run out of memory as a result and your guest's OOM killer may activate, killing important processes - https://www.kernel.org/doc/gorman/html/understand/understand016.html

Note that if you are passing through a physical PCI(e) device or a Virtual Function I/O (VFIO) Mediated device (MDEV) such as a vGPU, then ballooning will not work since these devices are mapped to fixed memory addresses in the host and in the guest. If you do enable ballooning, the KVM process will not release the memory back to the host but the guest may report a reduced memory availability which can be manually recovered using the KVM monitor using the balloon command.

Manually ballooning (testing)

In the monitor tab of your guest, type balloon <target_memory_in_mb> - so balloon 16384 will instruct your guest to target 16GB of memory. This is a 'target' which the driver on the VM side will try to reach by trying to free available memory.

Requirements for Windows VM

Installation

See Windows VirtIO Drivers to get info about

  • downloading VirtIO drivers
  • changelog and guest OS compatibility
  • other kind of guest devices supported

Download

Download the latest drivers (ISO) as suggested by the page Windows_VirtIO_Drivers to your desktop.

Then upload the ISO to your Proxmox VE server:

  • logon to the Proxmox VE web interface
  • select a ISO-enabled storage (see Storage_Model#Storage_type_Content)
  • switch to "content" tab
  • just use the "upload" button on the menu bar.

Choose the right driver

Enable Auto-Ballooning on Windows Server 2012 / Windows 8.1 or newer

Starting with virtio-win-0.1.173-2 the driver ISO provides an installer located at "<cddrive>:\virtio-win-gt-x64.msi" that can, besides other things, install the ballooning service.

If it does not work you can follow the manual way which is described below for Windows 2008r2.

Enable Auto-Ballooning on Windows 2008r2

  1. Set the VM memory to "Automatically allocate memory within this range" - I choose 4096/2048 as example (see screenshot)
  2. Start the VM and install all virtio drivers, including the balloon driver (see screenshot)
  3. Copy and rename as Administrator the WIN7\AMD64 directory from the virtio.iso to "c:/Program files/Balloon"
  4. Open a CMD as Administrator and cd into "c:/Program Files/Balloon"
  5. Install the BLNSVR with "BLNSVR.exe -i"

As soon as the service is started, also the memory information displayed on the Proxmox VE GUI is identical to the value shown in the windows task manager (see screenshot).

If you need details about ballooning stats for this VM, go to the KVM monitor and enter 'info balloon'

VirtIO drivers: KVM project wiki downloads

Enable Auto-Ballooning on Windows 2003 / Windows Xp

You need to install the balloon service with BLNSVR, like for win2008.

You also need to install the driver manually

Download the "devcon" software on microsoft website

http://support.microsoft.com/kb/311272

Then install the balloon driver with

devcon install BALLOON.inf "PCI\VEN_1AF4&DEV_1002&SUBSYS_00051AF4&REV_00"


See also

Requirements for Linux VM

Modern Linux Kernels does include the Balloon drivers by default. It works out of the box, and you only need to set the VM to "Automatically allocate memory within this range"

External Links

tbd.

Video Tutorials

tbd: Proxmox VE Youtube channel